DynaColor DH701 Manual de usuario

00P3H8020ZXSEC5 Integrated High Speed Dome Camera Outdoor User’s Manual Version 3.5

User’s Manual 91.2 Product Application Connect the Dome Camera to other devices as shown in the diagram to complete a video surveillance solution.

User’s Manual 10 2. Connecting the Dome Camera Please refer to the following sections to connect, set and operate the Dome Camera. In order to cont

User’s Manual 112.2 Switch/Connector Definition Configuring the Dome Camera’s ID and communication protocol are required before connecting the Dome

User’s Manual 12 2.3 Communication Switch Setting The Dome Camera’s communication switches are specified in the table below. Communication Switch

User’s Manual 132.4 ID Setting Please change the Dome Camera’s ID if there is more than one Dome Camera on the same installation site. Use the switc

User’s Manual 14 2.5 Camera Control Protocol Setting Define the protocol you are going to use basing on the devices of your surveillance system. Ge

User’s Manual 152.6 22-Pin Connector Definition An AC 24V Data Cable is shipped with the Integrated High Speed Dome Camera for a quick installation

User’s Manual 16 The Dome Camera’s 22-pin connector definition is listed as shown below. Pin Definition Cable Pin Definition Cable 1 AC 24-1

User’s Manual 172.7 RS-485 Connector Definition RS-485 is the interface that communicates the Dome Camera and its control device. Please connect th

User’s Manual 18 3 Operation and Configuration 3.1 Display Format The information shown on the screen are described in terms of OSD display, positi

User’s Manual 1Preface The information given in this manual was current when published. The company reserves the right to revise and improve its pro

User’s Manual 193.2 OSD Menu Tree The OSD setup menu structures of each model is listed separately in the following section. The star symbol indica

User’s Manual 20 Item Layer 1 Layer 2 Layer 3 Default MIN ANGLE <-10 ~ +10 DEG> 0 MAX ANGLE <080 ~ 100 DEG> 90 ANGLE ADJUSTER EXIT

User’s Manual 21Item Layer 1 Layer 2 Layer 3 Default DETECT MODE ON: <INT FOCUS>, <FIX FOCUS>, <FIX AE>, <MOTION>; OFF:

User’s Manual 22 3.2.2 P/M Model Item Layer 1 Layer 2 Layer 3 Default LANGUAGE <ENGLISH>, <JAPANESE>, <PORTUGUESE>, <SPANIS

User’s Manual 23Item Layer 1 Layer 2 Layer 3 Default PRESET SET <001>~<256> ENTER PRESET RUN <001>~<256> ENTER PRESE

User’s Manual 24 Item Layer 1 Layer 2 Layer 3 Default V CENTER<000> ~ <255> H SIZE <000> ~ <127> V SIZE <000>

User’s Manual 253.2.3 S3/S4/S5/S6 Model Item Layer 1 Layer 2 Layer 3 Default LANGUAGE <ENGLISH>, <JAPANESE>, <PORTUGUESE>, <

User’s Manual 26 Item Layer 1 Layer 2 Layer 3 Default PASSWORD <ON>, <OFF> OFF OSD AUTO CLOSE <OFF>, <5> ~ <30> S

User’s Manual 27Item Layer 1 Layer 2 Layer 3 Default DETECT MODE <MOTION> BLOCK MODE NONE; MOTION: <ON>, <OFF> FRAME SET

User’s Manual 28 3.3 Configuration Menu The detailed functions and parameter settings of your Speed Dome Camera can be set through the OSD (On Scree

User’s Manual 2 This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance w

User’s Manual 293.3.1 LANGUAGE The camera supports multi-language OSD operation; the available languages include English, Japanese, Portuguese, Span

User’s Manual 30 After completing setup of backlight, go back to the Main Page 1 and continue to set the focus relevant values. P/M Model: The Ba

User’s Manual 313.3.4 FOCUS The focus of the Dome Camera can be operated in two modes: Auto Focus mode and Manual Focus mode. Various setting for di

User’s Manual 32 P/M Model: • AUTO The optimum focus is achieved by the internal digital circuit. Users can adjust the minimum auto focus range for

User’s Manual 33Zoom Trigger Mode In this mode, AF is activated at the time when zoom is changed. PTZ Trigger Mode In this mode, AF is triggered wh

User’s Manual 34 3.3.5 AE MODE The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm ope

User’s Manual 35lens controls the amount of light reaching to the surface of the selected device. By increasing the F-stop number (F1.6, F2, F2.4, e

User’s Manual 36 • AGC With this option, the priority of AGC is higher than SHUTTER and IRIS; SHUTTER and IRIS circuit will function automatically

User’s Manual 37IRIS In this mode, the IRIS function adjusts exposure in higher property. SHUTTER speed and AGC circuit will function automatically

User’s Manual 38 3.3.6 WBC MODE A digital camera needs to find reference color temperature, which is a way of measuring the quality of a light sourc

User’s Manual 3 Cautions • Handle the camera carefully Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by imp

User’s Manual 39After WBC relevant parameter setups are completed, please exit the WBC MODE menu and go back to the Main Page 1 to continue to set o

User’s Manual 40 3.3.7 SETUP MENU 1 In Setup Menu 1, users could set Zoom Speed and choose whether to activate functions including Digital Zoom, Slo

User’s Manual 41NOTE: The difference between optical and digital zoom is that optical zoom uses the lens within the camera to draw the image closer

User’s Manual 42 • DIGITAL NOISE REDUCTION (P/S3/S4/S5/S6 Model) For S3/S4/S5/S6 models, with 2D / 3D Digital Noise Reduction (D.N.R.), the process

User’s Manual 43• APERTURE Under this setup menu, users can adjust enhancement of the edges of objects in the picture. G/V/T/S3/S4/S5/S6 Model:

User’s Manual 44 G/V/T/S3/S4/S5/S6 Model: P/M Model: 3.3.8 SETUP MENU 2 G/V/T/P/M Model: S3/S4/S5/S6 Model: • F

User’s Manual 45 NOTE: Flip setting is manual-controlled only. If a Preset or a point for other function (ex. Sequence) is set in the position that

User’s Manual 46 • PASSWORD (S3/S4/S5/S6 Model) The administrator can activate OSD Password function for security concerns. Once the function is tu

User’s Manual 47• OSD AUTO CLOSE (S3/S4/S5/S6 Model) Users can specify the duration for OSD menu to stay on the screen. Time selection ranges from

User’s Manual 48 3.3.9 ID DISPLAY Press the direction key down to turn the MAIN MENU page from 1 to 2, and then the menu item <ID DISPLAY> wil

User’s Manual 4 • Never face the camera towards the sun Do not aim the camera at bright objects. Whether the camera is in use or not, never aim

User’s Manual 49 TITLE SETTING: 01 0 1 2 3 4 5 6 7 8 9 EXIT A B C D E F G H I J SAVE K L M N O P Q R S T LEFT U V W X Y Z : / . , RIGHT [ ] + ? -

User’s Manual 50 3.3.12 PRESET • PRESET SET Totally 256 preset points can be set. Follow the steps below when in the preset setting menu. STEP 1:

User’s Manual 513.3.13 SEQUENCE The function executes pre-positioning of the pan, tilt, zoom and focus features in a certain sequence for a camera.

User’s Manual 52 • SPEED Users can set the pan/tilt speed of the Dome Camera from one sequence point to the next one, and the range of setup speed

User’s Manual 533.3.14 AUTOPAN Auto-pan means motion of scanning an area horizontally so that the Dome Camera can catch horizontal view. The paramet

User’s Manual 54 • DIRECTION The item is for setting the AUTOPAN direction of the Dome Camera. The Dome Camera will start to pan clockwise from th

User’s Manual 553.3.15 CRUISE CRUISE is a route formed with manual operation, through adjusting pan, tilt position and zoom parameters, which can be

User’s Manual 56 NOTE: Users could execute the cruise function through a keyboard. Please refer to the control keyboard’s quick guide for further

User’s Manual 57SEQUENCE LINE Select a sequence line that the Dome Camera should execute after the Return Time function is activated. The sequence l

User’s Manual 58 3.3.17 IR FUNCTION (Removable IR Cut Filter) With the IR cut filter, the Dome Camera can still catch clear image at night time or

User’s Manual 5Table of Contents 1. Overview...

User’s Manual 59P/M Model: Select one of the IR modes below through the right key on the control keyboard. Press the <CAMERA MENU> key (ENTER)

User’s Manual 60 while at value <13>, the camera comparatively tends to stay in B/W mode. IR COLOR When the IR function is removed, the video

User’s Manual 613.3.18 ALARM SETTING The Dome Camera provides eight alarm inputs and one alarm output (N.O. or N.C) to connect alarm devices. With t

User’s Manual 62 • ALARM ACTION The alarm actions include PRESET, SEQUENCE, AUTOPAN and CRUISE functions. Select one of these modes so that ce

User’s Manual 63• DWELL TIME The DWELL TIME is duration of executing an alarm action. If the PRESET mode is selected, the Dome Camera will go to

User’s Manual 64 3.3.19 ALARM DETECT When the alarm detect function is activated, the camera will detect movement within a monitoring area and then

User’s Manual 65The alarm will be triggered if the Exposure value changes; if the adjusted AE value retains for four seconds, the value will be save

User’s Manual 66 LEFT LIMIT Move the frame right/left using the right/left keys on the keyboard. TOP LIMIT Shift the frame up/down using the right

User’s Manual 67 P/M Model: • ON The camera will automatically execute motion detection within the monitoring area. NOTE: For P and M models, wh

User’s Manual 68 3.3.20 WDR FUNCTION The Wide Dynamic Range (WDR) function is especially effective in solving indoor and outdoor contrast issues to

User’s Manual 6 　 PASSWORD (S3/S4/S5/S6 Model) ... 46 　 OSD AUTO CLOSE (S3/S4/S5/S6 Model) ...

User’s Manual 69S3/S4/S5/S6 Model: G/V/T/P/M Model: NOTE: For P and M models, when WDR function is at AUTO or ON mo

User’s Manual 70 • PRIVACY SWITCH Users can enable or disable the Privacy Mask function through this item. Set this item to <ON> before conf

User’s Manual 71V SIZE (00~60) Users can adjust the vertical size of a privacy mask through this item. Set the H and V size to 0 can also delete the

User’s Manual 72 • SET MASK After pressing <ENTER> to enter the sub-menu of SET MASK, the Dome Camera will memorize the present position as

User’s Manual 732. Press <ENTER> to confirm the selection. Consequently, the screen will display the instructions to reset after the mask is c

User’s Manual 74 3.3.22 TIME SETTING The time setting function is used to set the TIME related parameters of the Dome Camera. Each item in the menu

User’s Manual 753.3.23 SCHEDULE The schedule function enables users to program a preset point or function (Sequence/Auto-pan/Cruise) automatically t

User’s Manual 76 AUTOPAN Users can select the AUTOPAN mode as an action carried out in a schedule point. CRUISE Users can select the CRUISE mode as

User’s Manual 77Appendix A: Technical Specification Items G Model M Model V Model P Model T Model CAMERA CCD Sensor 1/4" EXview 1/4"

User’s Manual 78 Items G Model M Model V Model P Model T Model Privacy Mask 24 8 24 8 24 Proportional Pan & Tilt On / Off (Pan and tilt s

User’s Manual 71. Overview The Dome Camera delivers up to 432x zoom ratio (T model) to capture clear image in the distance. Continuous Auto Focus, B

User’s Manual 79Items S3 Model S5 Model S4 Model S6 Model CAMERA CCD Sensor Sony CCD Optical Zoom 30× 36× Digital Zoom 1~12x variable NTSC 380

User’s Manual 80 Items S3 Model S5 Model S4 Model S6 Model Motion Detection On / Off Wide Dynamic Range On / Off Day/Night: IR Cut Filter

User’s Manual 81OSD Menu Notes The following OSD menu tables are provided for users to record various camera settings. <G/V/T Model> Item La

User’s Manual 82 Item Layer 1 Layer 2 Layer 3 Notes EXIT YES ID DISPLAY <ON>, <OFF> TITLE DISPLAY <ON>, <OFF>

User’s Manual 83Item Layer 1 Layer 2 Layer 3 Notes WDR FUNCTION <ON>, <OFF> PRIVACY SWITCH <ON>, <OFF> TRANSPARENC

User’s Manual 84 <P/M Model> Item Layer 1 Layer 2 Layer 3 Notes LANGUAGE <ENGLISH>, <JAPANESE>, <PORTUGUESE>, <SPANIS

User’s Manual 85Item Layer 1 Layer 2 Layer 3 Notes EXIT YES SEQUENCE LINE <1> ~ <8> SEQUENCE POINT <01> ~ <64> PR

User’s Manual 86 Item Layer 1 Layer 2 Layer 3 Notes EXIT + SAVE CLEAR MASK <01> ~ <08>, <RESET> MASK DISPLAY <FIRST&g

User’s Manual 87<S3/S4/S5/S6 Model> Item Layer 1 Layer 2 Layer 3 Notes LANGUAGE <ENGLISH>, <JAPANESE>, <PORTUGUESE>, <

User’s Manual 88 Item Layer 1 Layer 2 Layer 3 Notes OSD AUTO CLOSE <OFF>, <5> ~ <30> SEC. SYSTEM RESET <YES> DEFAULT

User’s Manual 8 1.1 Product Features Precise and Accurate Performance • Auto Calibration • Preset accuracy of 0.225° • Preset speed up to 400°/se

User’s Manual 89Item Layer 1 Layer 2 Layer 3 Notes BLOCK MODE NONE; MOTION: <ON>, <OFF> FRAME SET NONE; MOTION: <01> ~ <